Home Home Improvement The Complete Guide to Pump Servicing

The Complete Guide to Pump Servicing

96
0
SHARE

Pumps are a crucial part of any water system. They are used to move water and other fluids (e.g. gas) through pipes, tanks, and other containers. It can be used to create pressure so that the liquid is able to flow through pipes. This is why it is so important to make sure that your pumps are well-maintained and serviced regularly by pump servicing companies like Mega.

The Complete Guide to Pump Servicing

In this article, we will share with you things you need to know about pump servicing and the process of a simple pump service inspection.

What Do You Need to Know About Pump Servicing?

One of the best ways to keep your pool looking great all year round is by maintaining it properly. There are many different things that you can do to maintain your pool but one of the most important things is keeping an eye on the pumps in it. Pumps play a major role in circulating water throughout the pool and they can be very expensive if they break down. This article will list the steps that you should take to properly service your pool’s pumps.

1. Shut Off the Pump

The first thing that you need to do is shut off the pump to make sure it is off before touching it in any way. This will help prevent any accidental electric shock which could damage or kill your pump, especially if it is plugged in.

2. Open the Switches

There are three switches that you need to open to service your pump, one on the back of the motor unit, one on top of the motor and another on top of a vent located on either side of it. You should never service your pump without first opening these switches, otherwise you will not be able to get enough water out of the pump to service it.

3. Remove the Four Bolts

Located at the bottom of this unit are four bolts that need to be removed for you to pull off the motor unit from its housing.

4. Remove the Hose from Pump

The hose that comes out of your pump connects to a nipple on top which needs to be removed before you can take off the Unsafe Disconnect. To remove the hose, move the pump towards you and gently pull on the hose.

5. Remove Unsafe Disconnect

There are two screws that need to be removed in order to take off the Unsafe Disconnect. Make sure the pump is still connected to your bike’s frame and then unscrew these two screws in opposite directions while pulling on the wires to disconnect.

6. Take the Pump Out of Your Bike’s Frame

The pump should now be out of your bike frame, hold onto the aluminum frame and place a towel around it in order to protect it from scratches or dings.

7. Clean the Pump

After unscrewing the back of the pump, take a can of compressed air and spray into all openings of the pump. You may want to do this at the same time as you clean the pump filter. After unscrewing the back of the pump, take a can of compressed air and spray into all openings of the filter. to clean it.

8. Replace Filter

If the filter is a canister, unscrew the bottom of the canister and take out old filter and replace with new one.

9. Put Pump Back Together

Unscrew any other screws you can find on your pump. If you find screws that are too tight, use a wrench and make sure the screwdriver doesn’t slip off the screw head when turning it. Once all screws are removed, start putting together your pump by following these steps:

  • Put the base of your pump back on
  • Screw in any screws that were sticking out of the base
  • Put back together any pieces that may have fallen out during disassembly
  • Screw in any screws from outside the base as well

The Process of a Simple Pump Service Inspection

The process of pump inspection is a routine task that is performed by the on-site service technicians before, during and after every service call. It is an important step in the servicing procedure for pumps, as it helps to determine if there are any issues with the pump.

A simple pump service inspection involves checking for a few basic things:

  1. Condition of the bearings
  2. Condition of shaft and housing
  3. Condition of seals and gaskets
  4. Condition of suction cups or vanes

In brief, we have shared with you things you need to know about pump servicing and the process of a simple pump service inspection. Check out Mega if you are looking for an expert in pump servicing.

LEAVE A REPLY

Please enter your comment!
Please enter your name here